Brewly

The Brewly BWH30L is an efficient, compact 2500W semi-automatic brewer with adjustable malt basket for efficient sparging, bazooka bottom filter and tap. You mash, blanch and boil in the same vessel - Cooling coil sold separately. Via the clear digital display, you can easily set the temperature and time. Can also be used as a sparge water kettle.The malt is placed in a malt basket with a perforated insert that can be easily lifted up with the steel handle in two steps for easy leaching after mashing.Internally, there is a volume level gauge set on the stainless steel wall.Brewly BWH30L Brewery- Material: Polished stainless steel (AISI 304)- Brewing volume: 30 liters (max), at least 15L batches are recommended.- Total volume: 35 litres- Digital Controller with clear display - Set temperature and time.- Temperature range 25°C to 100°C, adjustable in steps of 0.1°C.- Temperature control up to 100°C, with +-1°C accuracy.- Power: 2500W in total (adjustable in 700W and 1800W, or both elements at the same time which gives 2500W). 10-16A fuse is recommended. The heating elements are placed under the base to avoid caramelization of the wort and to reduce burning.- Malt basket with steel handle: Can be raised in several steps.- Maximum recommended malt quantity is 8 kg.- Tap with Bazooka mesh-screen filter (raised Mesh-screen bottom filter for efficient separation of hops from the wort)- Strong glass lid- Height: 67 cm- Diameter: 36 cm (without handle and faucet)- Weight: 10 kg (freight carrying weight 40 kg)- Instruction manual- EU-power plug (UK power plug not included)- 220-240V 50/60Hz- Instructions Manual in EnglishMash water calculation:mash water in liters = (amount malt in kilos * 2,5) + 10L.Note: 2,5 is the ratio between water and malt, ie how thick the mash is going to be. This ratio can be varied between approx 2,2-3. 10L is the volume of water below the malt basket inside the brewery.Example: For a 20L recipe with 6kg malt the mash water calculation is as following: 6*2,5+10 = 25L.Sparging: For a 20L recipe, sparge with 78-degree C water up to the 25L mark, and then start the boil (you may start heating the wort while sparging to save time).

Brewery 30L with 8,8m chiller. The Brewly BWH30L is an efficient, compact 2500W semi-automatic brewer with adjustable malt basket for efficient sparging, bazooka bottom filter and tap. You mash, blanch and boil in the same vessel - Cooling coil chiller 8,8m included. Via the clear digital display, you can easily set the temperature and time. Can also be used as a sparge water kettle.The malt is placed in a malt basket with a perforated insert that can be easily lifted up with the steel handle in two steps for easy leaching after mashing.Internally, there is a volume level gauge set on the stainless steel wall.Brewly BWH30L Brewery- Material: Polished stainless steel (AISI 304)- Brewing volume: 30 liters (max), at least 20L batches are recommended.- Total volume: 35 litres- Digital Controller with clear display - Set temperature and time.- Temperature range 25°C to 100°C, adjustable in steps of 0.1°C.- Temperature control up to 100°C, with +-1°C accuracy.- Power: 2500W in total (adjustable in 700W and 1800W, or both elements at the same time which gives 2500W). 10-16A fuse is recommended. The heating elements are placed under the base to avoid caramelization of the wort and to reduce burning.- Malt basket with steel handle: Can be raised in several steps.- Maximum recommended malt quantity is 8 kg.- Tap with Bazooka mesh-screen filter (raised Mesh-screen bottom filter for efficient separation of hops from the wort)- Strong glass lid- Height: 67 cm- Diameter: 36 cm (without handle and faucet)- Weight: 10 kg (freight carrying weight 40 kg)- Instruction manual- EU-power plug (UK power plug not included)- 220-240V 50/60Hz- Instructions Manual in EnglishMash water calculation:mash water in liters = (amount malt in kilos * 2,5) + 10L.Note: 2,5 is the ratio between water and malt, ie how thick the mash is going to be. This ratio can be varied between approx 2,2-3. 10L is the volume of water below the malt basket inside the brewery.Example: For a 20L recipe with 6kg malt the mash water calculation is as following: 6*2,5+10 = 25L.Sparging: For a 20L recipe, sparge with 78-degree C water up to the 25L mark, and then start the boil (you may start heating the wort while sparging to save time).

Heat insulation for the Brewly BWH30L brewery & water heater. Provides faster heating, more vigorous boil and reduces energy consumption. Material: 5 mm neoprene foam.

Brewly 40L is an efficient, compact half-automatic brewery with Whirlpool, Hop Spider Wort Chiller with gardena-type connectors and mesh screen bottom hop filter.News:- Now a Brewly SS500 Hop Spider is included.- Now a Brewly Stainless Mash Paddle 60cm is included.- New open typ e malt basket for optimized wort flow.- A new heating element for reduced risk of burn-ins.The Brewly brewery opens up a world of possibilities to brew great craft beer with friends and family, and experience the pleasure to make beer at home that tastes as good as it does from a professional brewery.Mashing, lautering/straining, boiling and cooling takes place in the same pot. The mash is pumped around and heated according to the RIMS method. The Digital Controller provides simplicity in entering temperatures, times and power for both mashing and boil. Up to 9 mash steps and 9 hop/spice steps per recipe, and the memory can store up to 9 recipies.The malt is placed in a stainless malt basket with a perforated insert. The malt basket can easily be lifted in several steps for lautering/straining, and the insert can be adjusted seamlessly to fit the malt bill, thanks to a telescopic overflow-pipe.A polycarbonate sight glass lets you see the wort/beer volume up to 40L, and there is also a volume scale inside.A stainless Whirlpool tube is also included, making it possible to create a whirlpool in the wort which increases volume efficiency and speeds up the cooling of the wort.Brewly 40L Brewery with Chiller & Whirlpool- Material: Polished stainless steel (AISI 304)- Chiller: 8,8m stainless Cooling Spiral with gardena-type fittnings for easy connections- NEW! Brewly Hop Spider SS500 (500 mesh)- NEW! Brewly Mash Paddle 60cm- Whirlpool: Stainless Whirlpool tube with CAM-lock-connector- Adjustable flexible recirculation tube with CAM-lock-connector- Bottom filter: Mesh-screen bottom filter for efficient separation of hops from the wort.- Brewing volume: 40 liters- Total volume: 45 liters- Power: 2500 W, adjustable in 100 W steps. 16A fuse is recommended. The heating element is placed below the bottom to avoid wort caramelization.- Malt basket: Can easily be lifted in several steps for lautering/straining, and the insert can be adjusted seamlessly to fit the malt bill, thanks to a telescopic overflow-pipe. A Grainstopper avoids malt dropping through during mash-in. Max recommended malt weight is 10 kg.- Digital Controller with memory to store up to 9 recipies with up to 9 mash steps and 9 hop/spice steps each. Choose between Automatic Mode and Manual Mode with alarms and reminders.- Temperature range 25°C to 100°C, adjustable in 0,1°C steps.- Temperature control up to 100°C, with +-1°C accuracy.- Powerful magnetic centrifugal pump with seperate control. Max flow 12 liters per minute.- Tap with Bazooka mesh screen filter- Height: 57 cm (without lid and recirculation tube)- Diameter: 40 cm (without handles and tap)- Weight: 10 kg- EU-power plug (UK power plug not included)- 220-240V 50/60Hz- Instructions Manual in EnglishMash water calculation:mash water in liters = (amount malt in kilos * 2,5) + 10L.Note: 2,5 is the ratio between water and malt, ie how thick the mash is going to be. This ratio can be varied between approx 2,2-3. 10L is the volume of water below the malt basket inside the brewery.Example: For a 20L recipe with 6kg malt the mash water calculation is as following: 6*2,5+10 = 25L.Sparging: For a 20L recipe, sparge with 78-degree C water up to the 25L mark, and then start the boil (you may start heating the wort while sparging to save time).

Brewly 40L Brewery Kit is a affordable kit consisting of Brewly 40L Brewery & Brewly 20L Sparge water heater.For specifications, please see the product pages.

Heat insulation for the Brewly 40L brewery. Provides faster heating, more vigorous boil and reduces energy consumption. Material: 5 mm neoprene foam.

Brewly 70L is an efficient, compact half-automatic brewery for up to 60L batches with Whirlpool, Hop Spider, Wort Chiller with gardena-type connectors and mesh screen bottom hop filter.News:- Brewly SS500 Hop Spider is included- Brewly Stainless Mash Paddle 60cm is included- New improved malt basket allows more open wort flow to reduce risk of stuck mash.- New large surface heating element reduce risk of burn-ins.The Brewly brewery opens up a world of possibilities to brew great craft beer with friends and family, and experience the pleasure to make beer at home that tastes as good as it does from a professional brewery.Mashing, lautering/straining, boiling and cooling takes place in the same pot. The mash is pumped around and heated according to the RIMS method. The Digital Controller provides simplicity in entering temperatures, times and power for both mashing and boil. Up to 9 mash steps and 9 hop/spice steps per recipe, and the memory can store up to 9 recipies.The malt is placed in a stainless malt basket with a perforated insert. The malt basket can easily be lifted in several steps for lautering/straining, and the insert can be adjusted seamlessly to fit the malt bill, thanks to a telescopic overflow-pipe.A polycarbonate sight glass lets you see the wort/beer volume up to 60L, and there is also a volume scale inside.A stainless Whirlpool tube is also included, making it possible to create a whirlpool in the wort which increases volume efficiency and speeds up the cooling of the wort.Note: Effective brewing volume is 20-60 liters.Brewly 70L Brewery with Chiller, Hop Spider, Paddle & Whirlpool- Material: Polished stainless steel (AISI 304)- Chiller: 13m stainless Cooling Spiral with gardena-type fittnings for easy connections- NEW! Brewly SS500 Hop Spider (500 mesh)- NEW! Brewly Stainless Mash Paddle 60cm- Whirlpool: Stainless Whirlpool tube with CAM-lock-connector- Adjustable flexible recirculation tube with CAM-lock-connector- Bottom filter: Mesh-screen bottom filter for efficient separation of hops from the wort.- Brewing volume: 65 liters (recommended max)- Total volume: 75 liters- Power: 3500 W, adjustable in 100 W steps. 16A fuse is needed. The heating element with new larger surface is placed below the bottom to avoid wort caramelization.- Malt basket: Can easily be lifted in several steps for lautering/straining, and the insert can be adjusted seamlessly to fit the malt bill, thanks to a telescopic overflow-pipe. A Grainstopper avoids malt dropping through during mash-in. Max recommended malt weight is 15 kg.- Digital Controller with memory to store up to 9 recipies with up to 9 mash steps and 9 hop/spice steps each. Choose between Automatic Mode and Manual Mode with alarms and reminders.- Temperature range 25°C to 100°C, adjustable in 0,1°C steps.- Temperature control up to 100°C, with +-1°C accuracy.- Powerful magnetic centrifugal pump with seperate control. Max flow 12 liters per minute.- Tap with Bazooka mesh screen filter- Height: 69 cm (without lid and recirculation tube)- Diameter: 40 cm (without handles and tap)- Weight: 12 kg- EU-power plug (UK power plug not included)- 220-240V 50/60Hz- Instructions Manual in EnglishMash water calculation:mash water in liters = (amount malt in kilos * 2,5) + 10L.Note: 2,5 is the ratio between water and malt, ie how thick the mash is going to be. This ratio can be varied between approx 2,2-3. 10L is the volume of water below the malt basket inside the brewery.Example: For a 20L recipe with 6kg malt the mash water calculation is as following: 6*2,5+10 = 25L.Sparging: For a 20L recipe, sparge with 78-degree C water up to the 25L mark, and then start the boil (you may start heating the wort while sparging to save time).

Brewly 70L Brewery Kit is a affordable kit consisting of Brewly 70L Brewery & Brewly 40L sparge water heater.For more information, please see each product page.

Brewly 70L Brewery Kit is a affordable kit consisting of Brewly 70L Brewery & Brewly 20L sparge water heater.For more information, please see each product page.

Heat insulation for the Brewly 70L V2 brewery. Provides faster heating, more vigorous boil and reduces energy consumption. Material: 5 mm neoprene foam.

The Brew Kit 25L is the perfect complement to your automatic brewery - we've put together the things you need to start brewing. Just add bottles and Recipe Kits (ingredients).Brew Kit 25L contains:- 25-liter (30L max) fermenter with med tap och lid- 25-liter (30L max) fermenter with lid (no tap)- Fermenter air lock- Bottle filler (fits the fermenter tap)- Automatic pump siphon 44cm (Note: without holder and clamp)- Bench Capper Better Brew- Mash Paddle 52cm- Thermometer- Bottle Washer Spin Mini- SanitizerNote: Does not contain bottles or ingredients.