Cooling

Brewly Chiller 8,8m in Stainless Steel with optimized distance between the spirals for faster cooling of the wort. Includes Quick Connectors (3/4-inch) that are Gardena system-compatible.Suitable for breweries, pots and kettles up to 40L.Spiral diameter: ca 25 cmSpiral height: ca 25 cmTotal height: ca 39 cmCooling spiral length: 8,8 meters.

Brewly Chiller 13m in Stainless Steel with optimized distance between the spirals for faster cooling of the wort. Includes Quick Connectors (3/4-inch) that are Gardena system-compatible (as in image). Suitable for breweries, pots and kettles up to 70L. Cooling Spiral length: 13 metersSpiral diameter: ca 25 cmSpiral height: ca 35 cmTotal height: ca 52 cm

Brewolution Chiller 8,8m in Stainless Steel with optimized distance between the spirals for faster cooling of the wort. Suitable for breweries, pots and kettles up to 40L. Fittings and hose not included.Diameter 25 cm.Height 37 cm.

Brewolution Chiller 16m in Stainless Steel with optimized distance between the spirals for faster cooling of the wort. Suitable for breweries, pots and kettles up to 70L. Fittings and hose not included.Diameter 30 cm.Height 53 cm.

Brewolution Fittings and tubes Kit for Chiller 40 and 70. 2 x Fittings connector 3/8”, tap adaptor, tap connector and 2 x 1,5 m. tube is included.

Cooling Spiral 5m 3/4-inch Quick Connerctor compatible.Spiral diameter: 200 mmSpiral tube diameter: 10 mmSpiral height: 90 mmTotal height: 400 mm Max recommended kettle depth: 450 mmFittings: 3/4" for gardena

Cooling Spiral 7,5m in stainless steel for faster cooling of the wort. The fittings fit 3/4-inch Quck Connect garden hose connectors.Spiral tube diameter: ca 10 mmSpiral height: ca 90 mmTotal height: ca 400 mmTotal spiral diameter: ca 255 mmThreads: 3/4" (fit 3/4-inch Gardena-style garden hose connectors)

Cooling Spiral 15m in stainless steel for faster cooling of the wort. The fittings fit 3/4-inch Quick Connect garden hose connectors.Spiral tube diameter: 10 mmTotal diameter: 24 cmTotal height: 69 cmThreads: 3/4-inch (fit 3/4-inch Gardena-style garden hose connectors.)

These copper counter flow chillers are probably one of the fastest ways to chill wort. They are similarly efficient as the 30 plate chillers however they are easier to clean as they do not have all the small crevasses to trap hop material and other solids. The copper is a very good conductor of heat. These units are 23cm in diameter and about 18cm high. The input and output are approximately 10mm outside diameter. These can be used with gravity but are recommended to use with a pump. NOTE: Connectors/couplings are not included. 

With this Grainfather chiller you can cool the wort instantly as you pump it through the spiral, quick and easy. Hoses are included. This is the original Grainfather Counter Flow Wort Chiller. Coupling to Grainfather brewery is included, no other couplers are included.

Quick-Connect Gardena-type Hose Adapter, Quick Connectors 1/2" 12mm. Colour may vary

Quick-Connect Male Gardena compatuble 3/4". Colour may vary.

Quick-Connect Gardena-type Hose Adapter, 3/4" female to hose 1/2" (13mm inner diameter). Colour may vary.

Brewly TC-320 Digital Universal Thermostat. EU-version power cord (UK power cord not included).

Brewly AC-211 Digital Universal Thermostat. EU-version power cord (UK power cord not included). Can control one Heating source and one Cooling source. Sensor included.

Coobra Universal thermostat with EU-connections for cooling & heating at the same time and control both manually and via Wifi app.Perfect for home brewing, fermentation breeding, incubation, greenhouse, etc.- Intelligent digital display temperature controlled outlets- Temperature range -30 - 105 ℃- Supports both Celcius and Fahrenheit- WiFi 2.4GHz wireless connection- Mobile Smartlife APP control- Manual control or app controlled.- Double relay output: connect cooling & heating at the same time- automatic alarm for high/low temperature- temperature peak, Update once in 1s- Heating/cooling mode- temperature unit conversion- Programmable in up to 7 day intervals- compressor delay protection.- Temperature sensor with 150cm cord and suction cup for fastening.

Inkbird ITC-308 Digital Temperature Controller Outlet Thermostat with Dual Screen Readouts, w/Sensor. For Home Brewing & Fermentation, Breeding & Incubation, Greenhouse, Kombucha.- Plug and play design, easy to use. - Support reading with Centigrade or Fahrenheit. - Maximum output load: 1100W(110V) / 2200W(220V). - Temperature calibration, Compressor delay protection for refrigeration control.- High and low temperature alarms are available. - Dual relay output, be able to connect with refrigeration and heating equipment at the same time. - Dual display window, be able to display measured temperature and set temperature at the same time. - Heating/Cooling differential function could be set separately for refrigeration and heating to protect temperature controller from violent change.Specifications- Temperature Control Mode :On/Off Control, Heating and Cooling - Temperature Control Range : -40~100 °C / -40~212 ° F - Temperature Resolution: 0.1 ° C / 0.1° F ​- Temperature Accuracy: ±1°C (-50 ~ 70°C) / ±1°F (-50 ~ 160° F) - Ambient Temperature: -30~ 75 ° C / -22~ 167 ° F- Input Power: 100 ~240VAC, 50Hz/60Hz - Temperature Control Output: Max. 10A, 100V ~240V AC - Input Power Cable Length: 1.5m (5ft) ​- Output Power Cable Length: 30cm (1ft)- Sensor Type: NTC sensor (Including) - Sensor Length: 2m / 6.56ft ​- Sensor's probe dimension: 50mm x 6mm- Dimension Body: 140x68x33mm (5.5x2.7x1.3inch)- Socket (EU Version): 135x54x40mm (5.3x2.1x1.6 inch)

Inkbird WiFi ITC-308 Digital Temperature Controller Outlet Thermostat with Dual Screen Readouts, w/Sensor. For Home Brewing & Fermentation, Breeding & Incubation, Greenhouse, Kombucha.- Plug and play design, easy to use. - WIFI smart controller supports both IOS & Android，WIFI supports 2.4GHz Wi-Fi router, free APP “InkbirdSmart” which is able to monitor temperature at any time.- Support reading with Centigrade or Fahrenheit. - Maximum output load: 1100W(110V) / 2200W(220V). - Temperature calibration, Compressor delay protection for refrigeration control.- High and low temperature alarms are available. - Dual relay output, be able to connect with refrigeration and heating equipment at the same time. - Dual display window, be able to display measured temperature and set temperature at the same time. - Heating/Cooling differential function could be set separately for refrigeration and heating to protect temperature controller from violent change.Specifications- Temperature Control Mode :On/Off Control, Heating and Cooling - Temperature Control Range : -40~100 °C / -40~212 ° F - Temperature Resolution: 0.1 ° C / 0.1° F ​- Temperature Accuracy: ±1°C (-50 ~ 70°C) / ±1°F (-50 ~ 160° F) - Ambient Temperature: -30~ 75 ° C / -22~ 167 ° F- Input Power: 100 ~240VAC, 50Hz/60Hz - Temperature Control Output: Max. 10A, 100V ~240V AC - Input Power Cable Length: 1.5m (5ft) ​- Output Power Cable Length: 30cm (1ft)- Sensor Type: NTC sensor (Including) - Sensor Length: 2m / 6.56ft ​- Sensor's probe dimension: 50mm x 6mm- Dimension Body: 140x68x33mm (5.5x2.7x1.3inch)- Socket (EU Version): 135x54x40mm (5.3x2.1x1.6 inch)

INKBIRD ITC-310T-B is a dual relay thermostat which can be set to automatically control 12 individual temperatures for 12 time slots. It is widely used for homebrew, aquarium, pet breeding, hatching, fermentation, seed sprouting and etc.12 individual temperatures for 12 time slots: INKBIRD ITC-310T-B can be set 12 individual temperatures for 12 time slots. Once the practical temperature reaches its set temperature, its timer will be started automatically, which will be much better and more precise for the monitored creatures and/or plants.Wide application contexts: INKBIRD ITC-310T-B is widely used for homebrew, aquarium, pet breeding, hatching, barbecue, boiler temperature control, geothermal temperature control, heating pump constant temperature cycle, strain culture fermentation, seed sprouting, electric heating, electric oven, over-temperature protection and automatic temperature control system of all kinds of electrical equipment and etc.Flexible control mode: it supports single mode and cycle control mode; we can choose and/or switch the control mode based on our practical needs.Specifications INKBIRD ITC-310T-BTemperature Control Range: -50~120°C/-58~248°FTemperature Resolution: 0.1°C / 0.1°FMeasuring Accuracy: ±1°C (-50 ~ 70°C) / ±1°F(-58 ~ 158°F)Temperature Control Mode: On/Off Control, Heating and CoolingTiming Accuracy: 24 hours±1.7sTiming Range: 1~999 (min/hour/day)Periods of Time Max: 12 periodsCycle Setting: 1-999 times cycle, or 00 infinite cycleInput Voltage: 100 ~240VAC, 50Hz/60HzControl Output Current: Max.10AVoltage: 100~240V ACPower: Max.1200W(120V)/2200W(220V)Alarm: High and Low Temperature AlarmSensor Type: NTC Sensor(including)Sensor Length: 2m / 6.56ftRelay Output: Cooling(10A,100-240VAC)Heating(10A,100-240VAC)

The Brew Cooler is a waterproof, insulated cooling bag to keep correct fermentation temperature in fermenters up to 30L. Perfect if you dont have space or possibility to place your fermenter in a temperature controlled refrigerator at home.How the Brew Cooler worksThe function is simple, place your fermenter inside the Brew Cooler and add frozen water bottles (preferrably plastic) inside the Brew Cooler to reduce and keep the correct fermentation temperature. The volume of frozen water in the plastic bottles determines how many degrees below room temperature the fermenter will be kept at. The frozen water bottles should preferrably be replaced every 24 hours, or when needed.1. Place the Brew Cooler at a suitable location in your home. Place your fermenter with wort inside the Brew Cooler.2. Place the correct number of frozen water bottles inside the Brew Cooler according to the Temperature Chart below.3. Close Brew Cooler zip locks.4. After 24 hours, exchange the frozen water bottles for new ones.Temperature Chart: Choose the correct fermentation temperatureThis chart gives examples of the number and size of frozen water bottles that is needed for a given temperature reduction in the Brew Cooler for 20L beer.One 1-liter bottle reduce 1,5°C.Two 1-liter bottles reduce 3°C.One 1,5-liter bottle reduce 2°C.Two 1,5-liter bottles reduce 4°C.Three 1,5-liter bottles reduce 6°CFour 1,5-liter bottles reduce 8°C.One 2-liter bottle reduce 3°C.Two 2-liter bottles reduce 6°C.Three 2-liters bottles reduce 9°C.Four 2-liter bottles reduce 12°C.These temperature reductions are valid for 20L beer in the fermenter. As can be seen, the temperature reduction is about 1,5°C per liter frozen water. The maximum temperature reduction that can be archieved is about 15°C.Example: If your home ambient temperature is 21°C and you want to ferment 20L ale at 18°C, add one 2-liter or two 1L) frozen plastic water bottle together with your fermenter in the Brew Cooler. Exchange every 24 hours and repeat at least the first 3-4 days during the primary fermentation. If your brew 10L then about half the volume, 1-1.5L frozen water, is enough. What is the correct fermentation temperature?To get your home brew to taste as good as possible its important to control the fermentation temperature. An ale can theoretically be fermented at room temperature, 20-22°C, however it will taste the cleanest when fermented around 18°C, at least the first 3-4 days of fermentation. Lagers should be fermented at 10-12°C. Saisons can be fermented at high temperatures, 20-35°C, depending on the flavour profile you want.Brew Cooler 30L specificationsHeight: 60 cmLength 40 cmWidth: 40 cmMaterial: Tough black polyester Kraftig svart polyester with insulation and a grey water proof inner liner.Carrying strap: The Brew Cooler is equipped with an adjustable carrying strap.

The Brew Cooler XL is an extra large waterproof, insulated cooling bag to keep correct fermentation temperature in fermenters and kegs up to 30L. Either one 30L fermenter or two cornelius kegs fits inside. Perfect if you dont have space or possibility to place your fermenter in a temperature controlled refrigerator at home.How the Brew Cooler XL worksThe function is simple, place your fermenter or keg(s) inside the Brew Cooler and add frozen water bottles (preferrably plastic) inside the Brew Cooler to reduce and keep the correct fermentation temperature. The volume of frozen water in the plastic bottles determines how many degrees below room temperature the fermenter will be kept at. The frozen water bottles should preferrably be replaced every 24 hours, or when needed.1. Place the Brew Cooler at a suitable location in your home. Place your fermenter with wort inside the Brew Cooler.2. Place the correct number of frozen water bottles inside the Brew Cooler according to the Temperature Chart below.3. Close Brew Cooler zip locks.4. After 24 hours, exchange the frozen water bottles for new ones.Temperature Chart: Choose the correct fermentation temperatureThis chart gives examples of the number and size of frozen water bottles that is needed for a given temperature reduction in the Brew Cooler for 20L beer.One 1-liter bottle reduce 1,5°C.Two 1-liter bottles reduce 3°C.One 1,5-liter bottle reduce 2°C.Two 1,5-liter bottles reduce 4°C.Three 1,5-liter bottles reduce 6°CFour 1,5-liter bottles reduce 8°C.One 2-liter bottle reduce 3°C.Two 2-liter bottles reduce 6°C.Three 2-liters bottles reduce 9°C.Four 2-liter bottles reduce 12°C.These temperature reductions are valid for 20L beer in the fermenter. As can be seen, the temperature reduction is about 1,5°C per liter frozen water. The maximum temperature reduction that can be archieved is about 15°C.Example: If your home ambient temperature is 21°C and you want to ferment 20L ale at 18°C, add one 2-liter or two 1L) frozen plastic water bottle together with your fermenter in the Brew Cooler. Exchange every 24 hours and repeat at least the first 3-4 days during the primary fermentation. If your brew 10L then about half the volume, 1-1.5L frozen water, is enough. What is the correct fermentation temperature?To get your home brew to taste as good as possible its important to control the fermentation temperature. An ale can theoretically be fermented at room temperature, 20-22°C, however it will taste the cleanest when fermented around 18°C, at least the first 3-4 days of fermentation. Lagers should be fermented at 10-12°C. Saisons can be fermented at high temperatures, 20-35°C, depending on the flavour profile you want.Brew Cooler XL 30L specificationsHeight: 70 cmLength 40 cmWidth: 40 cmInternal supports: 60cm Vertical rib supports keeps the bag upright by itself.Material: Tough black polyester with insulation and a grey water proof inner liner.Carrying strap: The Brew Cooler is equipped with an adjustable carrying strap.Note: Fermenters, kegs or other accessories are not included.

New version with touch panel (LED). Control your fermentation temperature accurately, every time! Temperature control is one of the most crucial elements for producing a good quality beer. It needs to be regulated and stable throughout the whole fermentation process to ensure the yeast doesn't get stressed and ferments correctly to get the right flavour profile. With the ability to individually power and control the temperature of up to four Grainfather Conical Fermenters, each with their own fermenting schedules, the Grainfather Glycol Chiller is the perfect addition to ensure superior fermenting results.Design:With a sleek and compact design, that still accommodates our full array of features, the Glycol Chiller maintains the Grainfather’s principle of providing quality home brewing equipment, that deliver’s craft brewery like results, on a small footprint. With the addition of the Glycol Chiller, your system is operating at the ultimate level and you are even able to cold crash and lager down to 4°C (39°F). The Glycol Chiller connects to a hidden cooling sleeve, located in between the two stainless steel walls of the Conical Fermenter. Your desired temperature is dialed into the digital temperature controller on the Conical Fermenter, the liquid then travels through this sleeve, cooling the stainless steel which in turn cools the beer in the fermenter. The cooling sleeve never comes into contact with the beer, is completely concealed and does not need cleaning or sanitising - a true innovation for a fermenter on this scale.Features:- Allows you to cold crash 23 L (6 US Gal) of wort to as low as 4-6ºC (39-43°F). Minimum temperature will vary based on external factors such as ambient room temperature, the number of fermenters connected and other environmental conditions.- Cools and powers up to 4 Conical Fermenters at different temperatures and fermenting schedules.Note: The instructions for the Glycol Chiller will be attached to the outside of the shipping box. It is important that you retain these, do not throw them away and read them carefully before use to ensure no damage occurs to the unit. If these for any reason are not included with your purchase, we highly recommend you download a new copy via the instructions tab on this page and read them carefully.Glycol Chiller includes:- Wall outlet power cord with plug- 2 x cooling connection couplers- 2 x 2 m (6.5 ft) insulated hoses- 1 x Glycol Funnel- 1 x silicon tube for priming pump- 1 x 3 L (3 US qt) propylene glycolNOTE: When you receive your unit, you will need to fill it up with a propylene glycol mixture. Refer to the instructions provided with the Glycol Chiller for mixing, filling and pump priming information.Warranty:There is 24 month warranty for Glycol Chillers. Specifications:- Touch LED display panel- 6 L (1.5 US Gal) glycol tank- 300 W- 220 – 240 V, 50Hz- Noise level (operating): 50-60 dB- EU-version power cord (UK power cord NOT included).- 390W x 450D x 656H (mm)- Weight: 28.3 kg (62 lbs)InstructionsClick here to open the manual

With the Grainfather Glycol Chiller Adapter (GCA), you can easily control the temperature of your fermenter together with the Grainfather Glycol Chiller. Can be used in several models of fermenters and has both cooling and heating to provide a stable fermentation temperature.The kit consists of a cooling coil that is mounted through a rubber bung, which also has room for a airlock or blow-off, down into the fermenter. This coil is then connected to one of the channels on the Clycol Chiller.The control unit is of the same model as in Grainfathers Conical Fermenter Pro and handles the heating element and the glycol cooler's coolant pump to regulate temperature in the fermenter. It also supports Wi-Fi and the Grainfather App, which offers the user the ability to monitor and control the fermentation remotely. The unit's temperature probe is mounted on the outside of the fermenter or in a thermowell.The heating element is 30 W and is mounted with self-adhesive tape on the side of the fermenter.Specifications:Heating element - 12 V, 30 W. Dimension: 22 x 8 cm. Cord 2 mCooling coil - 5 m, 9 mm pipe outer diameter. The coil is 12 cm wide and 52 cm highTemperature probe - 35 x 6 mm. Cord 2 mControl unit - 12V. WiFI support, color display, Power cord 2 m.Cooling connection hoses - Insulation. length 2 meters, inner diameter 8 mm

Temperature control is one of the most crucial elements for producing a good quality beer. It needs to be regulated and stable throughout the whole fermentation process to ensure the yeast doesn't get stressed and ferments correctly to get the right flavour profile. The pump can handle cold water and glycol.To be able to cool with the Grainfather Conical Fermenter, you need to have the Conical Fermenter Temperature Controller. Then once your target temperature is below the temperature of the wort in your fermenter the Cooling Pump Kit pumps ice cold water or Glycol through the double walled insulated interior to cool down your wort. Simply connect the couplers and insulated hoses to the Conical Fermenter, submerge the submersible pump into a cooler box with water (add ice for your required temperature) and pump the liquid through the insulated cooling sleeve of the Conical Fermenter body.- Conical Fermenter Cooling Pump (submersible) that can handle Glycol.- T-section power connector.- 2 x brass couplers.- Rated 12 VDC – 4.8 Watts.

Use in conjunction with the Grainfather Connect Control Box thermometer, for accurate control of your wort transfer temperature through the Grainfather Counter Flow Chiller. Avoid long lag time and off flavours by using the Grainfather Wortometer. Adjust your wort and water flow rates from the Grainfather Counter Flow Chiller by dialling in the exact wort temperature your specific yeast requires. Requires a flexible 5-8 mm inner diameter silicon hose (not included). Instructions:https://www.grainfather.com/media/wysiwyg/V2_GF_WORTOMETER_INST_WEB.pdf

The 4” Lid with Coil Chiller is a exceptional brewing accessory designed for use with water, glycol chiller or similar systems. This tri-clamp 4” Lid with Coil Chiller will fit many fermenters e.g., Conicus Pro, Ss Brewtech, Brewtools, Brew Monk etc.  Perfect for Conicus Pro 55L. The core of this product is its stainless steel chilling coil. Immersed directly in your fermenting beer, it works efficiently to maintain ideal fermentation temperatures. The coil is crafted from high-quality stainless steel and is easy to clean, ensuring durability and reliability in your brewing process. Its length and width are thoughtfully designed to fit perfectly within the Conicus Pro 4" opening or similar systems.Installing the chilling coil is straightforward. It involves fitting the coil into the 4" opening and close it with the Tri-Clamp. For cooling, you will need an insulated tubing kit (either the one provided or your own), which connects the coil to your glycol chiller. This setup is vital for precise temperature control during fermentation, especially crucial when brewing lagers, which require colder fermenting temperatures.The 4" Lid with Coil Chiller also offers an efficient solution for cold crashing your beer. Cold crashing is a technique used to improve beer clarity and mouthfeel by bringing the beer to a low temperature, causing residual yeast and other particles to settle at the bottom of the fermenter.You can easily connect water, glycol chiller or similar systems to the inlet and outlet to the two male connections.We recomend bying the Conicus Pro 30 Insulation jacket with this Coil ChillerFeatures:521 mm long stainless-steel spiral cooler4" LidLid mounted two male connections for water or glycol chillerWith beer and Co2 postAISI 304 stainless-steelEasy to clean.Intergrated in the lid is a beer and CO2 post for carbonating and dispensing the beer. These posts are smart integral parts of the lid: one for adding gas (CO2) and the other for dispensing the liquid (beer).If you want to control the temperature during the fermentation the Conicus Pro can be mounted with this optional lid with a build-in cooling coil. This is a very simple, but effective way of controlling the temperature inside the fermenter.We recomend using the Ferminator for a more easy, effective and precise temperature regulating.This tri-clamp 4” Lid with Coil Chiller will fit many fermenters e.g., Conicus Pro, Ss Brewtech, Brewtools, Brew Monk etc.

The 4” Lid with Coil Chiller is a exceptional brewing accessory designed for use with water, glycol chiller or similar systems. This tri-clamp 4” Lid with Coil Chiller will fit many fermenters e.g., Conicus Pro, Ss Brewtech, Brewtools, Brew Monk etc. The core of this product is its stainless steel chilling coil. Immersed directly in your fermenting beer, it works efficiently to maintain ideal fermentation temperatures. The coil is crafted from high-quality stainless steel and is easy to clean, ensuring durability and reliability in your brewing process. Its length and width are thoughtfully designed to fit perfectly within the Conicus Pro 4" opening or similar systems.Installing the chilling coil is straightforward. It involves fitting the coil into the 4" opening and close it with the Tri-Clamp. For cooling, you will need an insulated tubing kit (either the one provided or your own), which connects the coil to your glycol chiller. This setup is vital for precise temperature control during fermentation, especially crucial when brewing lagers, which require colder fermenting temperatures.The 4" Lid with Coil Chiller also offers an efficient solution for cold crashing your beer. Cold crashing is a technique used to improve beer clarity and mouthfeel by bringing the beer to a low temperature, causing residual yeast and other particles to settle at the bottom of the fermenter.You can easily connect water, glycol chiller or similar systems to the inlet and outlet to the two male connections.We recomend bying the Conicus Pro 30 Insulation jacket with this Coil ChillerFeatures:338 mm long stainless-steel spiral cooler4" LidLid mounted two male connections for water or glycol chillerWith beer and Co2 postAISI 304 stainless-steelEasy to clean.Intergrated in the lid is a beer and CO2 post for carbonating and dispensing the beer. These posts are smart integral parts of the lid: one for adding gas (CO2) and the other for dispensing the liquid (beer).If you want to control the temperature during the fermentation the Conicus Pro can be mounted with this optional lid with a build-in cooling coil. This is a very simple, but effective way of controlling the temperature inside the fermenter.We recomend using the Ferminator for a more easy, effective and precise temperature regulating.This tri-clamp 4” Lid with Coil Chiller will fit many fermenters e.g., Conicus Pro, Ss Brewtech, Brewtools, Brew Monk etc.

This is a stainless-steel tri-clamp sample valve with a rotating rack arm mounted on a 3/8" tap with 13 mm barb. It is easy to mount.This valve can also be used for bottling directly from your Fermenter.This tri-clamp sample valve with racking arm will fit many fermenters e.g., Conicus, Ss Brewtech, Brewtools, Brew Monk etc.AISI 304 stainless-steel.Mounted valve for easy opening and closing.Easy to clean.Easy to mount.Tri-clamp standard.

This is a stainless-steel tri-clamp sample valve with a rotating rack arm mounted on a 3/8" tap with 13 mm barb. It is easy to mount.This valve can also be used for bottling directly from your Fermenter.This tri-clamp sample valve with racking arm will fit many fermenters e.g., Conicus, Ss Brewtech, Brewtools, Brew Monk etc.AISI 304 stainless-steel.Mounted valve for easy opening and closing.Easy to clean.Easy to mount.Tri-clamp standard.

Adapter that fits many types of kitchen faucets. The Faucet Adapter has four different threads, with two threads at each side of the adapter. This makes the adapter fit hose barb couplings, quick disconnects, wort chillers, bottle jet washers and similar.Threads:M22x1 female threadM24x1 male threadM22x1 male thread3/4" GHT male threadBefore installation it might be necessary to remove the aerator and gasket from the faucet. Install the Faucet Adapter gently, without damaging the threads of the kitchen faucet.Made of chrome-plated brass.One rubber gasket 22 x 3 mm included.